Saddle Fit - Fitting the Horse
This is critical for the horses comfort, attitude and being able to perform to their maximum potential without interference from the saddle.
Use the how-to video and pictures below for guidance on how to make a tracing of your horse's withers, rocker, and top line.
How To Make Tracings of Your Horse's Back
How To Take Tracings of a Horse/Mule Back
Thigh Measurements
The horse needs to be on level ground with all 4 feet flat on the ground with the head in a normal riding position when you take the following tracings.
There is no perfect way to fit a saddle to a horse/mule but we have found this to work really well for us and our customers! We don’t encourage one saddle for a horse, they change just like us! We help you choose the best saddle bar angle & rocker shape for your horses/mules. Our Remuda Saddle Fitting Pad sets you up with a very versatile saddle that will fit many horses/mules of all kinds. We will take into account if we see any muscle atrophy in the withers or if their top line/spine is dropped, you want a saddle that gives the horse room to fill back out to how they should be not how they are if possible.
First you have to determine where the “sweet spot” is located. This is right behind the shoulder blade where the front of the bars of any tree Western or English is meant to go. It is soft. Some horses it is easy to see especially if they have some muscle atrophy there.....this horse you can only feel but not see it.
Proper saddle/tree placement
*This is showing the front of the tree bar going right behind the should blade which is critical as the entire tree shape/design is meant to go there. On a finished saddle it is fine if the leather from the saddle goes beyond this point in front, in the back you don't want the leather to go past the cowlick on the flank as that will cause it to go up on the hindquarters and cause bridging, where pressure is in the front and back of the bars but not in the middle, which causes pressure points and pain.
You will need a saddle fitting tool! We highly recommend using a 24” piece of 12-2 Romex housing wire (has just the right amount of flexibility but holds its shape), FLEXIBLE RULERS ARE NOT ACCURATE they are too flexible and don't hold their shape! On the Romex wire put black electric tape on the ends, mark left/right & front/back on the ends. This process is called lofting, Bob learned this in boat building in his past. You can buy one of these "high tech" saddle fitting tools from us for $10.00 or make your own. Many electricians have scrape or many hard ware stores sell it by the foot.
Wither Tracing
Shape the wire over the withers, 3” behind the scapula/ “sweet spot”. Take your time and make sure the wire is exactly the same shape as the horse. Lay the wire on a piece of paper and trace the shape......see photo. You need to label left/right on the paper.
TIP:Put a piece of vertical tape or a vertical chalk line 3" back from the scapula on each side as a guide for where to shape the wire.
**Send us a picture of where you placed the wire and how you shaped it to help verify accuracy.
To help this make sense, we drew the shape of the saddle tree bars onto the horse so you can see the idea. On most saddles, if you search a little, you can see the front end tip of the tree bar and feel underneath the sheepskin for where the rest of the tree bar is located.
Rocker Tracing
Rocker = The shape/curve of the back from the scapula to the flank/cowlick area. Saddle tree bars have different rocker shapes, some straighter/flatter, some more arched/curved.
You bump the wire right behind the shoulder blade in that “sweet spot” 4” down parallel to the spine/center of back. Lay the wire on a piece of paper and trace the shape......see below. You need to do both sides and label which is front/back, which is left/right.
TIP: Put a piece of tape 4" down from the spine as a guide where to place the wire to shape it.
**Send us a picture of where you placed the wire and how you shaped it to help verify accuracy.
You can see where we are taking the tracing relates to the saddle tree bars which is the most important part for the horse. All of your weight is distributed on these bars and you want as close to 100% in contact as possible otherwise, you get excess pressure points that are painful.
Top Line Tracing
Place the wire in the center of the spine with the end of the wire even with the “sweet spot”. Lay the wire on a piece of paper and trace the shape......see below.
Tracing Wire Shapes Onto a Piece of Paper
Any paper will do as long as we can read it. You can even piece/tape together grocery sacks or newspaper! Now you have a record of your horses back! You can do this for each horse or mule and then compare them to see how much they are alike or different. It is good to recheck this several times in a riding season as the horses change with exercise etc. You can add new updated tracings to the same paper and date each one and watch for improvement or see if the problem is getting worse.